FAME混合ディーゼル燃料が機関/車両系に及ぼす影響
FAME Blended Diesel Fuel Impacts on Engine/Vehicle Systems
- 提供方法
- 本サイト上にてダウンロード・閲覧可
- 形態
- 価格
- 一般価格(税込)：￥1,100 会員価格(税込)：￥880
- 文献番号
- 20119375
- 文献・情報種別
- その他の国際会議
No.2011-01-1944
- 発行年月
- 2011年 8月
- 出版社
- その他・不明
- 言語
- 英語
- イベント
- PFL 2011
書誌事項
| カテゴリ（英） | FD2-4: Alternative Fuels for CI Engines 4 (Bio-diesel Fuels 4) 翻訳 |
|---|---|
| 著者（英） | 1) Naoki Kono, 2) Kazuo Yamamori, 3) Takafumi Furukawa, 4) Mike Noorman |
| 勤務先（英） | 1) TonenGeneral Sekiyu (Current Affiliation: Japan Petroleum Energy Center), 2) TOYOTA MOTOR CORPORATION, 3) TOYOTA MOTOR CORPORATION, 4) ExxonMobil Research & Engineering Co |
| 抄録 | FAMEのうち特にSMEによるB20燃料を燃料タンクに長期放置した場合の影響を9台の試験車で調べた結果，8ケ月目以降，金属タンク車の全てで始動不良など噴射系不具合が発生した．原因調査のため化学ラボでFAMEの酸形成，材料溶出，カルボン酸塩形成，重合について試験した．機関台上性能についてはFAME酸化の影響は無かった． |
| 抄録（英） | The impact of fatty acid methyl ester (FAME) blended diesel fuel on engine/vehicle systems was comprehensively investigated by vehicle, laboratory and engine tests. In this study, 20% FAME blended fuel (B20) was mainly used and soy bean oil methyl ester (SME) was primarily selected as the FAME. Vehicle testing with long-term fuel storage in vehicle fuel tanks was conducted, considering the most severe conditions in market use. Laboratory and engine tests were also conducted to better understand the vehicle test results. In the vehicle test, engine startability, idle roughness and fuel injection control were evaluated using nine vehicles with plastic or metal fuel tanks. All vehicles showed no problems up to 7 months. While five vehicles with plastic fuel tank did not show any problems throughout the test period up to 18 months, four vehicles with metal fuel tanks experienced malfunctions in engine start or fuel injection control following 8, 13, 13 and 18 months respectively. All problems experienced in the vehicles with metal tanks resulted from insufficient and unstable fuel pressure at common-rail of fuel system. The insufficient and unstable fuel pressure was caused by sticking of the suction control valve (SCV) in the fuel pump unit due to compounds accumulated on the SCV needle surface. Ester compound which is considered to be polymerized FAME was commonly observed in the accumulated compounds. Carboxylic acid salt was also detected as a component of the accumulated compounds. In one vehicle, rust was also detected in the accumulated compounds on SCV as well as inside of fuel injector. The five vehicles with plastic fuel tanks demonstrated no problems up to 18 months, though small amount of ester compounds, carboxylic acid salts and rust were detected on the inner surface of the SCV body of one of the plastic fuel tank vehicles. From the laboratory tests, it was found that carboxylic acids, carboxylic acid salts and polymerized SME can be formed when SME-blended diesel fuel was oxidized. Regarding the potential metal sources of the carboxylic acid salts, it was found that not only metal components but also some elastomers used in the fuel system release metals to the fuel. From the engine testing based on an industrial standard test protocol to assess engine torque loss owing to deposit formation, no significant engine torque loss was observed among fuels with various oxidation conditions regarding acid concentrations and Rancimat Induction Period values. 翻訳 |
