ログインしてください

文献・情報検索システム

日本語

ENGLISH

ヘルプ

ログインしてください

  • 詳細情報

Autoignition of Lubricating Oil from Piston Crown and In Cylinder Condition on Abnormal Combustion of Supercharged SI Engine

書誌事項

著者(英)1) Akira Seto, 2) Yuka Kuwae, 3) Junya Tanaka
勤務先(英)1) Kogakuin University, 2) Kogakuin University, 3) Kogakuin University
抄録(英)The supercharged spark ignition engine with direct fuel supply system in cylinder (SI engine) has a problem on abnormal combustion at low engine speed. It is called the LSPI (Low Speed Pre-Ignition)[1]. This research focuses on one of the source of abnormal combustion which is the autoignition of lubricating oil from piston crown in cylinder, here especially, frequency of autoignition in cylinder[2,3,4]. In this experiment, the test engine operates without spark ignition as motoring operation. The advantage of this method is to avoid the effect of gasoline dilution[5,6]. Namely, it is able to reveal the essence of abnormal combustion experimentally. The 2 kinds of lubricating oil are tested. The measured data show that the frequency of autoignition in this research is 1/10 of that of lubricating oil scattering from piston crown. The abnormal combustion occurs the frequency of 1 time in each 10000 cycles approximately. The special behavior of the LSPI has been measured. The autoignition timing is ATDC in the initial stage. When the cycle of autoignition proceed, its timing is advance to BTDC. On the other hand, the time history of pressure and temperature in cylinder are able to evaluate the autoignition by Livengood-Wu integral[7]. The activation energy E which is estimated by the integral means the quantitative evaluation of autoignition in cylinder. The dangerous activation energy E for the LSPI is under 6452(×104 J/mol)in this research. The activation energy E would be able to take advantage of the engine design and simulation to prevent from the LSPI.

翻訳

検索について

閉じる

検索ボックスの使い方

検索条件は最大5件まで入力可能です。検索ボックスの数は右側の「+」「−」ボタンで増減させることができます。
一つの検索ボックス内に、複数の語句をスペース(全角/半角)区切りで入力した場合、入力した語句の“すべてを含む”データが検索されます(AND検索)。
例)X(スペース)Y →「XかつY(を含む)」

「AND」「OR」プルダウンの使い方

「AND」を指定すると、前後の検索ボックスに入力された語句の“双方を含む”データが検索されます。また、「OR」を指定すると、前後の検索ボックスに入力された語句の“いずれかを含む”データが検索されます。
例)X AND Y →「XかつY(を含む)」  X OR Z →「XまたはZ(を含む)」
AND検索とOR検索が混在する場合は、OR検索が優先されます。
例)X AND Y OR Z → X AND (Y OR Z)
AND検索と複数のOR検索が混在する場合も、OR検索が優先されます。
例)W AND X OR Y OR Z → W AND (X OR Y OR Z)

検索フィルタの使い方

検索結果の件数が多すぎる場合など、さらに絞り込みしたいときに「検索フィルタ」を使います。各項目にチェックを入れると、その項目が含まれるデータのみに検索結果が絞り込まれます。
各項目後ろの「()」内の数字は、その項目が含まれるデータの件数です。

検索のコツ

著者名で検索するときは、「自動車 太郎」のように、姓名をスペースで区切って入力してください。