ログインしてください

文献・情報検索システム

日本語

ENGLISH

ヘルプ

ログインしてください

  • 詳細情報

Aerodynamic Optimization Using Add-On Devices: Comparison Between CFD and Wind Tunnel Experimental Test

書誌事項

著者(英)1) Massimiliana Carello, 2) Marco Verratti
勤務先(英)1) Politecnico di Torino, 2) Politecnico di Torino
抄録(英)JUNO is an urban concept vehicle (developed at the Politecnico of Torino), equipped by an ethanol combustion engine, designed to obtain low consumptions and reduced environmental impact. For these goals the main requirements that were considered during the designing process were mass reduction and aerodynamic optimization, at first on the shape of the car body and then, thanks to add-on devices. JUNO’s aerodynamic development follows a defined workflow: geometry definition and modelling, CFD simulations and analysis, and finally geometry changes and CFD new verification. In this paper the results of the CFD simulations (using STARCCM+ and RANS k-ε) with a corresponding 1/1 scale wind tunnel tests made using the real vehicle. Particularly, the results in term of: total drag coefficient (Cx), total lift coefficient (Cz), the total pressure in the side and rear analyzing twenty different aerodynamics configurations made up of different combination of some aerodynamics add-on devices. From the analysis of the results is emerged that CFD simulations using RANS k-ε methods are able to predict the trend of total drag coefficient and its absolute value. Regarding the trend and the absolute value for lift coefficient, much larger deviation than Cx has been identified. For total pressure scene, there is a high similarity between the two ways of testing, especially on the side and on the central rear zone. The CFD results simulations, RANS k-ε model is correct to develop and test symmetrical wide body. The obtained results are in good agreement with experimental wind tunnel results but, with particular attention to geometry, that suddenly change the way of air-flow.

翻訳

検索について

閉じる

検索ボックスの使い方

検索条件は最大5件まで入力可能です。検索ボックスの数は右側の「+」「−」ボタンで増減させることができます。
一つの検索ボックス内に、複数の語句をスペース(全角/半角)区切りで入力した場合、入力した語句の“すべてを含む”データが検索されます(AND検索)。
例)X(スペース)Y →「XかつY(を含む)」

「AND」「OR」プルダウンの使い方

「AND」を指定すると、前後の検索ボックスに入力された語句の“双方を含む”データが検索されます。また、「OR」を指定すると、前後の検索ボックスに入力された語句の“いずれかを含む”データが検索されます。
例)X AND Y →「XかつY(を含む)」  X OR Z →「XまたはZ(を含む)」
AND検索とOR検索が混在する場合は、OR検索が優先されます。
例)X AND Y OR Z → X AND (Y OR Z)
AND検索と複数のOR検索が混在する場合も、OR検索が優先されます。
例)W AND X OR Y OR Z → W AND (X OR Y OR Z)

検索フィルタの使い方

検索結果の件数が多すぎる場合など、さらに絞り込みしたいときに「検索フィルタ」を使います。各項目にチェックを入れると、その項目が含まれるデータのみに検索結果が絞り込まれます。
各項目後ろの「()」内の数字は、その項目が含まれるデータの件数です。

検索のコツ

著者名で検索するときは、「自動車 太郎」のように、姓名をスペースで区切って入力してください。